*(MAK-90 to AK-47 Drill Fixture
is $45.00 due to pins and
bushing included)
There are
NO
restrictions on the ownership of
the drilling fixtures used for
CLASS II conversion &
construction. There are NO
restrictions on the books that
detail the CLASS II conversion &
construction step by step. All
NFA RULES APPLY TO THE USE OF A
DRILLING FIXTURE TO PERFORM A
CLASS II CONVERSION or
CONSTRUCTION PROJECT.
PARTS FOR SALE
ARE INTENDED FOR USE AS
REPLACEMENT PARTS ONLY FOR
REGISTERED RECEIVER WEAPONS. ALL
NFA RULES APPLY.
(All Sales on Class II Drilling
Fixtures are FINAL, Returns NOT
Accepted.)
AR-15
to M-16
The fixture is a drilling
template made of machined steel
that properly places the hole
above the selector for the GI
auto sear pin. A bolt is used to
hold the fixture in place and
the top of the fixture is
aligned parallel with the top of
the receiver to align sear pin
hole. There is a washer that is
used to allow the fixture to
clear the "selector stops" on
the receiver. There is still a
small amount of milling that has
to be done to allow for
clearance for the sear in the
receiver but that is explained
in the fixture instructions and
may be done with a dremel or on
a drill press.
$30.00
Semi to Full Auto AK-47
The fixture is a drilling
template made of machined steel
that properly places the sear
pin hole in the receiver for the
auto sear pin. There are
machined steel pins that are
used to hold the fixture in
place on the receiver. There is
still a small amount of
dremeling that has to be done to
the carrier rail to allow for
clearance for the trip in the
receiver but that is explained
in the fixture instructions, and
may be done with a dremel. Since
the holes are two different
sizes on the AK-47 a bushing is
provided for the right side hole
to guide the bit that is the
same size as the bit to
eliminate the need to center
punch this hole.
$45.00
M-11/9 semi to M-11/9 SMG
The fixture is a drilling
template made of machined steel
that properly places the
selector switch hole in the
receiver for the full auto
selector. A bolt is used to hold
the fixture in place and the top
of the fixture is aligned
parrallel with the top of the
receiver to align selector hole.
$30.00
H&K(All Types) The fixture is a drilling
template made of machined steel
that properly places the take
down pin hole in the semi-auto
receiver to allow for the
installation of a full auto push
pin lower.
$30.00
FULL AUTO
CLASS II MANUALS
AR-15 to
M-16 Full Auto Vol. 1(Blueprints
Drop In Auto Sear)
:
$12.00
Semi AK to
Full Auto AK-47 Class II
Construction Manual:
$12.00
How to built a
STEN from a Kit Book (includes
receiver template):
$20.00
H&K 91 to
G3 Full Auto Full Auto Class II
Construction Manual -
$12.00
MAC-10 45 or
9mm (Covers M-11/380) Open Bolt
Semi to Full Auto manual
(Covers
SMG Trigger Parts Assembly M-10
or M-11) -
$12.00
COBRAY
M-11/9 9mm Semi Auto to Full
Auto Manual (NOT using
SMG Parts)-
$12.00
M1 semi to
M2 full auto carbine manual :
$12.00
AK-47 Full Auto Bolt Assy
w/recoil spring PLUS AK-47 Full
Auto Trigger Set w/Rate Reducer
$175.00
AK-47 Full Auto Bolt Assy
w/recoil spring
$125.00
AK-47 Full Auto Trigger Set
w/Rate Reducer
$69.99
ROMANIAN MFG. NICE !!!!!
AK-47 Full Auto Auto 5pc. Part
Set
$49.99
ROMANIAN MFG. NICE !!!!!
M-16 Bolt Carrier
$99.99
M-16 Fire Control Trigger Group
$75.00
M-16 GI Full Auto F/C Parts Set
w/M-16 Bolt Carrier
$150.00
M-16/AR-15 Blueprint and Forged
Lower Receiver Blank
$65.50
THE little
BLACK LOWER PLUS an AR-15 Lower
Receiver FORGING BLANK This
Booklet describes the milling
and manufacturing of lower(s).
Working through job plans it
guides the builder from first to
last step of construction,
giving hints and pointers on the
process. The little BlacK Lower
starts with the milling process
and takes you all the way to
surface finishings. This kit
includes: (3)three 17" x 24" to
scale blue line prints ~ 8"x11"
booklet w/18 pages &
illustrations Plus the
following: AR15 M16 Lower
Receiver Forging (NO FFL
Required) This is an M16 or
AR-15 lower in unfinished state,
(current US contract) with all
the reinforcement updates. As it
is unfinished, no FFL is
required and is 100% legal in
the USA. In its current state,
it is a great paperweight. The
receiver can be finished by any
competent machinist.
